超音速气流磨(粉碎机组)Supersonic Speed Jet Mill (Pulverizer Unit)
品牌
其他厂商性质
成都市所在地
双锥真空干燥机Double Cone Rotating Vacuum Drier
面议节能型振动流化动态干燥机 Energy-s**ing Vibro Fluidized Dynamic Drier节能型振动流化床
面议热风循环烘箱Hot Air Circulating Oven
面议湿法造粒机Wet Pelletizer
面议高速离心喷雾干燥机组High-speed Ce***ifugal Spray Drier Unit高速喷雾干燥机
面议中药浸膏专用干燥机组Dedicated Drying Unit for Chinese Medical Extract中药浸膏喷雾
面议热泵烘干机Heat Pump Drier
面议大风量快速烘干热风循环烘箱Rapid Drying Hot Air circulating oven with a Large Air Flow大风量烘箱
面议内外加热输送带式真空干燥机Inner and Outer Heating Conveyer Belt Type Vacuum Drier
面议方形真空干燥机、圆形真空干燥机Square/Round Vacuum Drier
面议内热搅拌沸腾(流化)强化干燥机Internal Heating, Stirring and Boiling (Fluidized) Intensification Drier
面议沸腾(流化)制粒干燥机Boiling (Fluidized) Pelletizing Drier
面议一、工作原理及应用范围介绍 Introduction of Working Principle and Scope of Application
本机组以干燥洁净的压缩空气为动力源,通过气流高速喷射,使粉碎室内形成一个粉碎、分级圆面,并在粉碎室内形成压力差,则物料自动吸入粉碎室,在4到16个喷头所喷出的超音速气流作用下(产生冲击能E=1/2mv2),物料在分级圆面上作高速运动(通常在2-3马赫内)使物料作相互高速高能的摩擦、碰撞、撕裂等作用,从而达到超细粉碎之目的。
适用于莫氏硬度1-7级各类干燥脆性物料,物料粒度100-400目,含水量低于3%,本机可进行粉碎的物料非常之广,例如:各种矿石、化工、电子、农药、医药、中药等各类产品,并适合热敏性、低熔点物料。产品粒度一般可达到1-10μm,粒径≤20μm,有些物料甚至可达到0.5-0.1μm。
The dry and clear compressor air is adopted as power source of this equipment; under the high-speed jetting of air flow, one pulverizing and grading disc, as well as pressure difference are formed in the pulverizing chamber, thus to automatically absorb the materials in the pulverizing chamber; under the actions of supersonic speed air flow jetted from 4-16 sprayers (impact energy E=1/2mv2), the materials move at high speed on the grading disc (generally within 2-3mach) to generate friction, compact and tear with high speed and energy, thus to realize the superfine pulverizing purpose.
It is applicable to various dry and brittle materials with Mohs hardness of 1-7, particle size of 100-400 meshes and water content lower than 3%. This equipment can be used for many materials, such as various minerals, chemicals, electronics, pesticides, medicines and traditional Chinese medicines, and is applicable to materials with heat sensitivity and low melt point. In generally, the particle size of materials is 1-10μm with maximum of ≤20μm; for some materials, it can up to 0.5-0.1μm.
二、特点Characteristics
1.高速气流粉碎,物料在粉碎工程中不会有大的升温。
2.本系统因粉粹出来的产品细度非常细,属于高精超微加工设备,对于提升产品的性能、功能以及价值有作用。
3.粉碎过程无噪音,自动化程度高。
4.特别适合粉碎热敏性物料以及要求很细的脆性物料。
1. The high-speed air flow is adopted for pulverizing, no significant temperature rising caused during the pulverizing process.
2. This is high-accurate and superfine processing equipment due to the high fineness degree of pulverized products, and has unit effects in improving property, function and value of products.
3. There is no noise generated during the pulverizing, and it is high in the degree of automation.
4. Especially, it is applicable to pulverizing of heat-sensitivematerials and brittle materials with high finesses requirement.
三、工艺流程图Process flow diagram
四、技术参数(下表中数值仅供选型时参考)
Technical parameters (the values in the table below are for reference in type selection only)
超音速气流粉碎机