品牌
其他厂商性质
所在地
特点介绍:
1、系统压力均不低于17.5Mpa,设备运行高效节能。
The system pressure is not lower than 17.5Mpa,and the equipment runs efficiently and saves energy.
2、公司专门的高射速加大油路设计,射速200mm/s左右,设备运行稳定并且低阻低噪音。开合模周期控制在3秒左右,开模位置重复精度偏差小于1.5mm。
The company's special high firing rate and increased oil circuit design,firing rate of about 200mm/s, stable equipment operation.low resistance and low noise.The mold opening and closing period should be controlled at about 3 seconds. and the deviation ofrepeated precision of mold opening position should be less than 2mm.
3、大螺杆高转速配置,的提高塑化效率,提升注射速率,的缩短模生产周期。
The configuration of large screw with high rotation speed can maximize plasticizing efficiency,increase injection rate andshorten mold production cycle.
4、标配高速机电脑和高响应电磁阀,标配欧普康电子尺,以确保系统响应速度及精度。
The standard configuration includes the Meng Li high-speed machine computer and the northern precision machine solenoidvalve.The standard configuration includes the Oupukang electronic ruler to ensure the system response speed and accuracy.
5、料筒加热标配陶瓷加热圈,螺杆塑化设计具有高效率、高混色及高耐磨性。As standard,Easton computer and Heithecker oil pump.oil research and North Seiki solenoid valves, and Opcom electronicruler are standard to ensure the accuracy of system response speed.
6、标配油温检测显示和机械手、针阀接线端子排。
Standard oil temperature detection and display.terminal block of manipulator and needle valve.
技术參数 SPECIFICATION | KS130/IU480 | KS170/IU480 | KS220/IU990 | KS260/IU1250 | KS320/IU1680 | KS360/IU1680 | |||||||||||||||||||||||
注射部份 INJECTION UNIT | A | B | A | B | A | B | A | B | A | B | A | B | |||||||||||||||||
注射容积 Shot Volume | cm3 | 276 | 350 | 277 | 350 | 560 | 677 | 713 | 848 | 990 | 1234 | 990 | 1234 | ||||||||||||||||
注射量(PET) Injection Weight | g | 255 | 322 | 255 | 322 | 510 | 616 | 650 | 772 | 910 | 1135 | 910 | 1135 | ||||||||||||||||
螺杆直径 Screw Diameter | mm | 40 | 45 | 40 | 45 | 50 | 55 | 55 | 60 | 60 | 67 | 60 | 67 | ||||||||||||||||
螺杆长径比 Screw L/D Ratio | Sc | 22:1 | 21:1 | 22:1 | 21:1 | 22:1 | 21:1 | 22:1 | 21:1 | 22:1 | 21:1 | 22:1 | 21:1 | ||||||||||||||||
注射压力 Injection Pressure | Mpa | 251 | 318 | 254 | 318 | 393 | 476 | 475 | 565 | 510 | 635 | 510 | 635 | ||||||||||||||||
对空注射速率 Injection Rate | cm3/s | 175 | 138 | 175 | 138 | 177 | 146 | 176 | 148 | 170 | 136 | 170 | 136 | ||||||||||||||||
塑化能力(PET) Plasticzation Capacity | g/s | 33 | 45 | 33 | 45 | 68 | 85 | 85 | 105 | 105 | 122 | 105 | 122 | ||||||||||||||||
螺杆转速 Max Screw Speed | rpm | 300 | 300 | 300 | 300 | 300 | 300 | ||||||||||||||||||||||
注射速度 Injection Speed | mm/s | 200 | 200 | 200 | 200 | 180 | 180 | ||||||||||||||||||||||
注射行程 Injection Stroke | mm | 220 | 220 | 285 | 285 | 350 | 350 | ||||||||||||||||||||||
合模部份 CLAMPING UNIT | | | | | | | | ||||||||||||||||||||||
合模力 Clamping Force | Kn | 1300 | 1700 | 2200 | 2600 | 3200 | 3600 | ||||||||||||||||||||||
移模行程 Clamping Stroke | mm | 380 | 430 | 500 | 550 | 620 | 700 | ||||||||||||||||||||||
拉杆内间距 Space Between Tie Bar (WxH) | mm | 430*410 | 470*470 | 530*530 | 610*570 | 660*660 | 710*680 | ||||||||||||||||||||||
模板距离 Max. Daylight | mm | 840 | 930 | 1050 | 1150 | 1270 | 1450 | ||||||||||||||||||||||
容模厚度 Max. Mold Height | mm | 460 | 500 | 550 | 600 | 650 | 750 | ||||||||||||||||||||||
最小容模厚度 Min. Mold Height | mm | 145 | 145 | 160 | 180 | 220 | 250 | ||||||||||||||||||||||
顶出行程 Ejector Stroke | mm | 120 | 120 | 140 | 150 | 180 | 180 | ||||||||||||||||||||||
顶出推力 Ejector Force | Kn | 34 | 34 | 68 | 68 | 125 | 125 | ||||||||||||||||||||||
电控部份 CONTROL UNIT | | ||||||||||||||||||||||||||||
电机功率 Motor power | Kw | 31 | 31 | 47 | 60 | 67 | 67 | ||||||||||||||||||||||
电热功率 Heater Power | Kw | 11 | 11 | 15 | 17 | 20 | 20 | ||||||||||||||||||||||
温度控制区 No.of Heater Control Zone | zone | 4 | 4 | 5 | 5 | 5 | 5 | ||||||||||||||||||||||
系統压力 System Pressure | Mpa | 17.5 | 17.5 | 17.5 | 17.5 | 17.5 | 17.5 | ||||||||||||||||||||||
其他 | | | | | | | | ||||||||||||||||||||||
油箱容量 Oil Tank Capacity | L | 400 | 400 | 550 | 600 | 700 | 700 | ||||||||||||||||||||||
重量(约) Machine Weight | T | 4 | 5.3 | 7 | 9 | 12 | 14 | ||||||||||||||||||||||
外型尺寸 Machine Dimension (LxWxH) | M | 4.3x1.2x1.9 | 4.9x1.4x1.9 | 5.2x1.45x2.0 | 5.7x1.5x2.2 | 6.2x1.6x2.2 | 6.6x1.65x2.2 |
本网站所有技术参数仅供参考,本公司保留修改技术参数的权利,恕不另行通知。All technical parameters of this website are for reference only. The company reserves the right to modify the technical parameters without notice.
高排量的液压系统设计,动力系统加大,注射速度比同类型产品提高15%,模循环周期缩短10-15%,全面提升注塑机表现,可满足高标准的成型要求
油路板分布在各执行元件位置,响应速度快,动态性能好,注塑过程更快速,产品成型更好
注射单元采用模组化的托板座设计,一线式双缸平衡注射装置,使螺杆在注塑过程中受力均匀,显著提高射胶稳定性,使料筒定位更加准确
高刚性的宽模板设计,配合高安全系数的拉杆,整体提升合模结构的刚性及稳定性
伺服驱动器在锁模保压冷却等阶段能输出压力但保持速度接近零速,因而功率消耗小,更节能
料筒采用纳米远红外高效节能加热装置,改善了传统加热圈电热转换效率低、热传导率低、表面温度高“两低一高”缺点,比传统加热圈节能30%-40%
控制面板采用彩色屏幕,实时监测生产进程,并显示各种故障诊断,操作更省心
人性化工艺参数设置,设置急停开关,动作全面监控,保护工作人员人身安全